Ingalls 35640-35650 User Manual download pdf

ING3565-102099

Installation Instructions

Removal Instructions

1. IMPORTANT! Check alignment and document the readings. Determine the amount of camber change needed before proceeding.

This kit will give -1 to +3 of camber change.

2. Raise vehicle in a safe manner and support vehicle on jack stands under body and remove the tire/rim assembly.

3. Remove the cotter pin and nut from the upper ball joint. Break the taper free between the upper ball joint and spindle and remove

the ball joint stud from the spindle.

4. Inspect the ball joint stud and spindle for any abnormal wear. If damaged, replace the spindle and ball joint.

5. Remove and discard the two nuts holding the upper ball joint to the control arm and remove the ball joint.

6. Press out and discard the two studs from the ball joint.

Assembly Instructions

1. Slide the small bracket into the large C shaped bracket with the studs of the small bracket protruding through the slot in the C

shaped bracket. If difficult to slide, pull on the protruding studs and gently tap the brackets together. Do not tap on the studs.

2. Place the ball joint over the two studs pressed into the new C shaped bracket (not the small bracket) with the ball joint stud at the

same end as the open end of the C shaped bracket.

3. Install two of the new flange head lock-nuts onto the studs protruding through the ball joint bracket and torque to 35-40 ft-lbs (47-54

N-m).

Installation

1. Install the new camber bracket on the bottom side of the control arm with the studs of the small bracket protruding through the

existing holes of the control arm.

2. Install the remaining two flange head lock-nuts onto the studs protruding through the control arm. Tighten the nuts enough so the

assembly is secure but still slides against the control arm.

3. Reinstall the ball joint stud to the spindle. Torque the nut to 29-35 ft lbs (39-48 N-m) and install the cotter pin (if the cotter pin does

not line up with the hole, tighten the nut so the next slot is aligned with the cotter pin hole).

4. Reinstall the tire/rim assembly and remove the vehicle from the jack stands.

5. Install alignment equipment and set the camber to the manufacturers specifications by sliding the adjustable camber bracket to the

proper position. Tighten the two flange head lock-nuts to 35-40 ft-lbs (47-54 N-m).

6. Check and set toe to specifications, road test vehicle and make further adjustments as needed.

Limited Warranty

Subject to Disclaimer. All Ingalls products are warranted against defects in materials and workmanship for ninety (90) days from date of purchase. During the warranty period, Ingalls will repair, or at its option replace at no

charge, components that prove to be defective. The product must be returned, shipping prepaid, to Ingalls facility. This limited warranty does not apply if the product is damaged by accident or misuse. The foregoing

warranty is in lieu of all other warranties expressed or implied including but not limited to any implied warranty of merchantability, fitness, or adequacy for any particular purpose or use Ingalls shall not be liable for any

special, incidental or consequential damages whether in contract, tort, or otherwise resulting from the use of or the inability to use the product.

WARRANTY DISCLAIMER

Use of this product in competition, or use on vehicles altered from original manufacturer's specifications or settings, EXPRESSLY VOIDS WARRANTY. The user is urged to inspect for suspension binding or interference

when the product is used in these manners. However, due to the varying conditions and manner of use which the product will be subjected to in such uses, Ingalls Engineering Co., Inc. makes no warranties, either express or

implied, including any warranty of merchantability or fitness for a particular purpose for use in competition or with specifications or setting other than those specified by the original manufacturer's specifications.

Installation Instructions 1

Summary of Contents

Page 1 - Installation Instructions

ING3565-102099 Installation Instructions Removal Instructions 1. IMPORTANT! Check alignment and document the readings. Determine the amount of ca

Comments to this Manuals

No comments

Ingalls 35640-35650 User Manual

Browse online or download User Manual for For the car Ingalls 35640-35650. Ingalls 35640-35650 User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for For the car Ingalls 35640-35650